Home > Cisco Asa > Cisco Asa Ssh Username Not Working

Cisco Asa Ssh Username Not Working

Contents

SSH Connection Failed You receive this error message on the ASA: %ASA-3-315004: Fail to establish SSH session because RSA host key retrieval failed. well, now they do have the means. This is the "global" password not the password associated with a user. The default password is cisco. http://haiteq.com/cisco-asa/cisco-asa-rdp-not-working.php

If I have NOT defined aaa authen/author lines, I can log in with a public key and no global username statement. We want SSH. Related Products This configuration can also be used with the Cisco ASA 5500 Series Security Appliance with software Versions 9.x and later. Here's the long-winded StackExchange answerer version: Cisco authentication is kind of a mess for a beginner.

Asa Ssh Access Denied

However, the security appliance requires that all Telnet traffic to the outside interface be protected by IPsec. thanks. Your minimum requirement, by default and by common sense, is to set a simple password: router(config-line)# login router(config-line)# password cisco Now, you will be asked for a password, and you will

New 32x8 modem on the Approved List [ComcastXFINITY] by maxbrando188. Omair Khalid September 24, 2012 at 11:59 Thankx alot, saved my travel back to office. I've verified >> that the username/pass is correct(it works through the ASDM) and that SSH >> access is allowed from the relevant IP range(I get to a password prompt), >> but Enable Ssh Cisco Asa 5505 cisco cisco-asa ios share|improve this question edited Nov 28 '11 at 8:27 Hangin on in quiet desperation 89.1k9116202 asked Nov 14 '11 at 13:45 Alain O'Dea 4323921 How are

One big difference is that a simple password is no longer good enough. Cisco Asa Ssh Connection Refused And while you're at it, set up an encryption key pair: router(config)# username admin privilege 15 secret EncryptedPassword router(config)# line vty 0 15 router(config-line)# transport input ssh router(config-line)# no password router(config-line)# interface GigabitEthernet1/3 nameif outside security-level 0 ip address 1.1.1.1 255.255.255.128 ! After I have configured ssh access (assigned a domain, generated my rsa key, and enabled ssh), I am unable to log in.

Aaron ConawayI like to lean my head to the left, hit it with the palm of my right hand, and document what knowledge falls out.More Posts - Website Related Posts:Recap - Cisco Asa Ssh Password Authentication Failed Note: There's always the chance some other input can generate the same hash, but statistically it's a very low (read: negligible) probability. ForumsJoin Search similar:[HELP] Cisco ASA 5520 Setup and Management Port Setup[Config] Clients can't get out on Cisco ASA 5505[HELP] Routing issuesturn asa into "router"[Config] ASA open some ports? The security appliance supports the SSH remote shell functionality that is provided in SSH Versions 1 and 2 and supports Data Encryption Standard (DES) and 3DES ciphers.

Cisco Asa Ssh Connection Refused

ciscoasa(config)# crypto key generate rsa ciscoasa(config)# ssh x.x.x.x y.y.y.y If this is an 8.4(2) or greater implementation that is an upgrade of an ASA that already accepts SSH, there is click here now interface GigabitEthernet0/0 nameif LAN security-level 0 ip address 172.30.186.2 255.255.254.0 ! Asa Ssh Access Denied The privilege 15 part allows you to bypass user mode entirely. Asa Ssh Server Unexpectedly Closed Network Connection Better for each admin to have their own private password/key. –Marwan Jan 8 '15 at 12:38 enable elevates priv.

The "Approved Devices List" page has now been totally remodeled [ComcastXFINITY] by telcodad426. http://haiteq.com/cisco-asa/cisco-rdp-not-working.php I again SSH into the firewall with my ACS credentials and proceed to issue the enable command followed by the newly set password. Main menu Skip to content Uncategorized Can't Login to Your ASA via SSH or Telnet? up vote 5 down vote favorite 1 I have created a test user that is set to privilege 15 in the config: username test password **************** encrypted privilege 15 When I Configure Ssh On Asa

As it turns out, however, all those password commands are deprecated. (Or if they're not, they should be.) That's why you have the following two options: router(config)# enable password PlainText router(config)# I'd also bet money that equivalent PIX OS versions do that same, so keep an eye out. Any thoughts on why this may be happening? >> >> Network Engineer, JNCIS-M >> > 214-981-1954 (office) >> > 214-642-4075 (cell) >> > jbrashear [at] hq >> http://www.speakeasy.net >> _______________________________________________ >> http://haiteq.com/cisco-asa/cisco-asa-ftp-not-working.php Was this Document Helpful?

It thinks the password is bad, but only when done via SSH. Set Telnet Password Cisco Asa You cannot use the no telnet command with the telnet timeout command. They did change something a while back where ssh was concerned requiring a user account.

share|improve this answer answered Aug 1 '12 at 18:48 Bad Dos 62839 If there are usernames entered in the config or an external auth server, the pix will use

I haven't run into this issue with other ASAs that are configured identically and I can login to the other ASAs from the same terminal window so it shouldn't be something Can anybody advise what type of connector this is? Furthermore, there's no secret equivalent command from line configuration mode, so you're stuck with obfuscated passwords there. Cisco Asa Enable Ssh Asdm Cisco recommends that you use SSH for a more secured data communication.

There's a lot of legacy baggage there. Any thoughts on why this may be happening? Telnet Configuration In order to add Telnet access to the console and set the idle timeout, enter the telnet command in global configuration mode. http://haiteq.com/cisco-asa/cisco-ssl-vpn-rdp-not-working.php ftp mode passive pager lines 24 mtu LAN 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 route LAN 172.18.36.0 255.255.255.0 172.30.186.1 1 timeout

Pick Randomly Between -1 or 1 Can Newton's laws of motion be proved (mathematically or analytically) or they are just axioms?

>