If you're OK with the results, you can just keep using them and spare yourself the trouble with OpenVPN configuration. On that same tab set the Wireless Network Name (SSID) to exactly the same SSID as your primary router you will be connecting to over wireless. So I probably need to check the rules in the other tables nat mangle and raw other than the filter table. I changed WAN MAC and problem was solved. (Setup>>MAC address clone...) (In my case WAN an WLAN was the same MACs) share|improve this answer answered Mar 16 '14 at 1:31 Erik
Even if something were wrong (it looks fine to me as the 255.255.255.255 is the result of a routing rule targeting a single host instead of a network), your router still http://ipaddress.com If this is working fine, we can begin with the VPN configuration. That may not work with all hardware though, and may be why Tomato does it via a bridge. As a backup, I'm trying to configure a DLINK DIR-615 on which I have loaded DD-WRT.
You have two options: Switch the Tomato router to Router mode, which disables NAT on the WAN interface. Spanish Hide My Ass! How to prove that authentication system works, and that the customer is using the wrong password? Dd Wrt Client Bridge Setup In Windows, that would be the TCP/IPv4 settings of the network adapter that is connecting your computer to the internet.
That 1st router has been working for years as it is today and I have no desire to change that. Dd Wrt Wireless Mode Ap Yes, my password is: Forgot your password? One interesting thing we can see is that packets are going to the NOTRACK target, and also to the DROP target. French Hide My Ass!
Paste the following line in the text area:iptables -t nat -I POSTROUTING -o `get_wanface` -j SNAT --to `nvram get wan_ipaddr`Click the the “Run Commands” button. Dd Wrt Client Vs Client Bridge IP subnets: A common problem is that devices are unable to "see" each other when they are in different IP subnets; for example if the DSL-Modem is using 192.168.0.1 and the This can be done by going to Advanced > Routing in the Web interface. Yes, router 2's WAN is connected to the LAN port of router 1.
You are done and the Client router should connect to the AP within a minute or so. http://www.tomshardware.com/answers/id-2365228/connectivity-problem-wrt-client-mode.html I have configured the 'Wireless Mode' to 'Access Point', but also have to configure the WRT54GL to be in either 'Gateway mode' or 'Router mode', what is the correct setting for Dd-wrt Client Bridge Mode specific to DDWRT) Routing (DD-WRT) confusion - Help Needed Configure DD-WRT as a router   6 Replies Ghost Chili OP Thanks A.J. Dd-wrt Client Mode and this Quote: x.y.14.213 * 255.255.255.255 UH 0 0 0 eth0 x.y.14.212 * 255.255.255.252 U 0 0 0 eth0 doesnt seem corret!
Network Basic Layout: Modem--->Router 1 (DD-WRT)--->Switch---> [WAN Port] Router 2 ((Tomato(VPN)) Firewall Rules for Router 2: iptables -A INPUT -s 192.168.1.0/24 -j ACCEPT | iptables -I FORWARD -s 192.168.1.0/24 -j ACCEPT When your network, the router(s) and the VPN are working fine, you can still convert your network to a WLAN (so making it wireless). There are several ways to configure your DD-WRT router with OpenVPN, all are listed in the article: DD-WRT OpenVPN Setup It is a good idea to get someone in "real-life" with Go to Setup > Basic Setup.
DD-WRT Community Contact Development News Forum Wiki Bugtracker Blog Quick Links Log in Profile View unanswered posts Log in Username: Password: Log me on automatically each visit basic routing not Dd Wrt Client Bridge Routed Hit SAVE (not apply) NEXT go to the Wireless -> Basic Settings and change the Wireless Mode to Client. Perhaps I'm misunderstanding something?
Have you tried AP mode on the DD-WRT router? WEP will often work as well, but it is not a secure form of encryption. Reason: Typo in the problem definition statement [email protected] View Public Profile View LQ Blog View Review Entries View HCL Entries Find More Posts by [email protected] 09-19-2010, 10:08 PM #2 Assuming your computer is already connected to the DD-WRT router (which is likely, since you're able to access the webconfiguration), you now need to change the network settings of your computers
You may need to unplug the router for 17 seconds if the router doesn't reset. up vote 12 down vote favorite 1 I have one DD-WRT router (herein: 1st) connected to the Internet, working perfectly, with client PCs assigned static IP addresses. OpenVPN is not included in MICRO or MINI firmware versions, so with them you can only use PPTP or L2TP protocol. Router 2 can access and see everything but Router 1 cannot.
Boy Network Guru Member Router mode means NAT translation is applied to packets going to and from the WAN port. Set your computer back to auto IP and auto DNS if you like. Join our community today! Get back to http://dd-wrt.com/site/support/router-database, download a different one.
Using transistor as switch, why is load always on the collector Proving convergence of real sequence Did Trump call Belgium a village in Europe? Should I trust a website which breaks when I use a complex password? "president-elect" grammatically correct? your computer). asked 1 year ago viewed 360 times active 1 year ago Related 0How does iptables masquerading allow to access a different local subnet?1I need some help proof reading my IPtables rules,
No, I have not disabled DHCP on either devices as I need DHCP services on both (ie: need dhcp for the local clients (lan) that connect to the linksys. Boy said: ↑ Router mode means NAT translation is applied to packets going to and from the WAN port. It took me a while to find the appropriate firmware version of this device. Isn't the BBC being extremely irresponsible in describing how to authenticate an account-related email?
NAT is supposed to be handled by the kernel's netfilter (modules nf_nat*) and iptables is the management tool for netfilter. The Router you are configuring is the client router. What power do I have as a driver if my interstate route is blocked by a protest? So far so good, but for some reason the clients that are connected through the 2nd router can't see the Internet.
It doesn't look like I can now change/edit the username to something other than what is currently setup. From both Wan and Lan segments, the router is pingable. So, it seems to be a routing issue. NOTE: If the client router is externally managed, such as in a college dorm etc., you should Go to Setup -> Basic Setup and set the WAN port protocol to what