Home > How To > Copy Running-config Tftp Not Working

Copy Running-config Tftp Not Working

Contents

Sign in to make your opinion count. Use the ping command to verify connectivity. Components Used This document is not restricted to specific software and hardware versions. Code ladder, Robbers Why were pre-election polls and forecast models so wrong about Donald Trump? have a peek at these guys

How to find the file where a bash function is defined? Sign in to report inappropriate content. Rating is available when the video has been rented. It simply did not work in my lab. https://supportforums.cisco.com/discussion/11708571/using-command-copy-running-config-tftp

How To Copy Startup-config To Tftp Server

Accessing tftp://10.66.64.10/backup_cfg_for_my_router... Router(config)#kron policy-list SaveConfig Router(config-kron-policy)#cli write Router(config-kron-policy)#exit cli--Specifies EXEC CLI commands within a Command Scheduler policy list. recurring--Identifies that the occurrence is to run on a recurring basis. Jay Christopher 71,311 views 3:01 HD - Cisco IOS Image Backup and Restore/Upgrade via TFTP - Duration: 9:16.

Router#copy tftp: running-config Address or name of remote host []? 64.104.207.171 Source filename []? The information in this document was created from the devices in a specific lab environment. Loading... How To Backup Cisco Switch Configuration Always test them to see that they will operate as expected in case of real need.Ready to test your skills for the CCNA exam?

Connect to the router either via console cable, Telnet or SSH. 3. Cisco Copy Running Config To Startup Config Note: You can also use startup-config to copy the config saved in NVRAM rather than the running-config. Additionally, running-config has ‘loopback 9' that isn't in R1-1.txt. https://www.petri.com/forums/forum/networking/cisco-routers-switches-how-to/65037-copy-running-config-to-starup-config-isn-t-working copy running-config tftp tftp-ip-addr filename - Use this command to upload a copy of the running configuration file from the Layer 2 Switch or Layer 3 Switch to a TFTP server.

You should not copy-paste configuration with more than 2000 characters into CLI. Restore Cisco Switch Config Using Putty NOTE It is recommended to use a script or the copy running-config tftp command for extensive configuration. Or some manual configuration needed (besides setting an IP address so you can talk to a tftp server) in order to replace a defective or misconfigured switch. If we use the ‘configure replace', only the ‘loopback 1' interface will remain.

Cisco Copy Running Config To Startup Config

Problem Solved –cgasp Sep 24 '13 at 19:53 add a comment| up vote 2 down vote The copy command (at least with Cisco boxes) allows you to specify the username and Stelios is currently working as a VoIP Engineer in a Telecom company, where he uses his knowledge in practice. How To Copy Startup-config To Tftp Server Instead of trying to push it it from the router, why not pull it from the backup server? How To Copy Config From Cisco Switch Using Putty Paul Browning 50,647 views 2:36 Using a TFTP Server with Cisco Equipment - Duration: 9:52.

Restoring a Running Router with Basic ConfigurationIn case the router has the basic configuration (i.e. Copy configuration from TFTP server to the router[Router name] #copy TFTP runAddress or name of remote host []?172.16.10.2Source filename[]?/Backup/Router01.cfg[router name]#show run[router name]#show interfaces[router name]#copy run startMy Advice: Save This Article in All rights reserved. | Terms of Use | Privacy Policy FastIron Ethernet Switch Administration Guide Supporting FastIron Software Release 08.0.30 Part Number: 53-1003625-01 JavaScript must be enabled in order to use Hot Network Questions How does Gandalf end up on the roof of Isengard? Copy Tftp

router ports are assigned to subnet), use the command copy TFTP run and then complete the rest of the requirements like this:[router name]# show run -- to see the running configuration[router Patrick Sullivan 51,242 views 8:00 HOW TO BACKUP ROUTER CONFIGURATION USING TFTP SERVER - Duration: 8:56. The Capture Text window appears. check my blog Cons: need confirmation, press enter.

Always save them in safe and secure places. Cisco Tftp Download Issue the exit command in order to return to the Router# prompt. Copy the running configuration file to the TFTP server: CE_2#copy running-config tftp: Address or name of remote host []? 64.104.207.171 Destination filename [ce_2-confg]?

Sign in Share More Report Need to report the video?

Loading... Loading backup_cfg_for_router from 64.104.207.171 (via FastEthernet0/0): ! [OK - 1030 bytes] 1030 bytes copied in 9.612 secs (107 bytes/sec) CE_2# Use an FTP Server to Backup and Restore a Configuration In Text based configuration files offer a lot of flexibility for administrators who understand how to work with them. How To Backup Cisco Router Configuration Using Putty This makes the router do the heavy lifting of determining the differences and the iterations of commands required to reach that configuration.

Lab colleague uses cracked software. Enter Y if you are sure you want to proceed. ? [no]: y Loading R1-1.txt from 192.168.2.2 (via FastEthernet0/0): ! [OK - 6487 bytes] Loading R1-1.txt from 192.168.2.2 (via FastEthernet0/0): ! Using the ‘configure replace' command would add those two commands. On the HyperTerminal menu, choose Transfer > Capture Text.

To Provide a telnet PasswordRouter#config tRouter(Config)#line vty 0 4Router(Config)#loginRouter(Config)#password [password name]Press [Ctrl][z] and issue sh run to ensure that password has been setb. Paste the configuration file into the router by selecting Edit > Paste to Host on the HyperTerminal menu. Linked 16 Automate configuration backup (every minute) in Cisco IOS Related 14BGP “no synchronization” command not showing up in running-config8Suppress confirmation prompts in IOS when copying files1Cisco IOS: Service Config0SSH configuration Add to Want to watch this again later?

PeteRouter_Backup !! 7400 bytes copied in 0.548 secs (13504 bytes/sec) PeteRouter# 4. Especially the individual port configuration stuff. Remember you have restored the running-config you would need to issue a "copy run start" command to make this config persistent (i.e. Create a kron occurrence--This informs the router when and how often the policy should run.

This feature is invoked with ‘time' paramater and used to undo changes when the configuration is not confirmed. Sub-subcommands must have two leading spaces. IT Track 16,822 views 8:38 how to configure privilege passwords, line console passwords on cisco router - Duration: 2:18. Log in > Go to enable mode > issue a "copy running-config tftp"* command > Supply the IP address of the TFTP server > Give the backup file a name.

>