My boss asks me to stop writing small functions and do everything in the same loop The case of the Maid, the Son and the Butler Pick Randomly Between -1 or Then run the command to load it. We do have Texstar. I cannot lower the speed to 800GHz :-( It was not clear to me if you installed cfu or not.
Check them out below. Common errors: - Do you have proper administration rights? (super-user?) - Is the governor you requested available and modprobed? - Trying to set an invalid policy? - Trying to set a But trying: $ sudo cpufreq-set -c 0 -u 1200000 It does. etc.
The governor "performance" may decide which speed to use within this range. The governor "powersave" may decide which speed to use within this range. The task seems to stay on one processor long enough to get it above 20%.
Is the untested/empty statement true? There are only two governors available for this driver, which are Performance and Powersave. CPU Speed: 800 GHz but cpufreq-info and i7z_GUI gives 1.8-2.3GHz which is true ... Cpu Frequency Scaling Indicator Press Ctrl + X and then Y to save.
Why were pre-election polls and forecast models so wrong about Donald Trump? No Or Unknown Cpufreq Driver Is Active On This Cpu Most of the settings in the examples should be the same or close to the same for any other distros. For example. So, it's not a thermal issue. –Michael Goldshteyn Aug 23 '12 at 18:48 add a comment| Your Answer draft saved draft discarded Sign up or log in Sign up using
If not here are the commands to load the modules. current CPU frequency is 800 MHzCha-ching!!!Bonus Tip! Kernel version Make sure your kernel version is at least 2.6.12 to make use of all the possible governors that will be mentioned. lsmod | grep freq If you see most or all of modules that where listed in the cpufreq directory then your done. How To Run Indicator-cpufreq
I am reluctant to offer advice to others to modify their system based on my uninformed guesswork!Hopefully someone who knows what they're doing will come along to help.One question - have Ubuntu Intel Pstate maglin Guest Re: CPUfreq ondemand is not working « Reply #3 on: March 10, 2012, 05:18:49 AM » There is a bit of general discussion on cpufrequtils in an Archlinux post Why is "Try Again" translated to やり直す?
Adv Reply August 1st, 2010 #8 ferossan View Profile View Forum Posts Private Message 5 Cups of Ubuntu Join Date May 2007 Location Santiago, Chile Beans 32 DistroUbuntu 10.10 Maverick Many thanks. Any ideas? Cpufreqd Remove any userspace CPU scaling programs There are some userspace programs that can be run to scale the processors frequency.
http://forums.opensuse.org/english/g...t-problem.html Thank You, My Blog: https://forums.opensuse.org/blogs/jdmcdaniel3/ Software efficiency halves every 18 months, thus compensating for Moore's Law Its James again from Austin, Texas Reply With Quote 11-Mar-2012,15:15 #10 tkmbe View Profile Adv Reply June 18th, 2010 #4 ferossan View Profile View Forum Posts Private Message 5 Cups of Ubuntu Join Date May 2007 Location Santiago, Chile Beans 32 DistroUbuntu 10.10 Maverick maglin Guest Re: CPUfreq ondemand is not working « Reply #9 on: March 10, 2012, 06:06:00 AM » It seems to have an available driver then?I don't really have any useful Should I report it?
How? You can decide which one you fits your needs best. Should you wish to use the acpi frquency control, you will need to boot with the kernel parameter intel_pstate=disable. Your rc.local could look like the following example which sets the ondemand governor and the up_threshold to 20%.
cpu is set to 800MHz and stays with this frequency!! Move on to the next section. The battery is required to supply the peak demand and ensure correct system operation Are you using the battery set in? I followed the steps in the wiki and I get this::: Setting cpufreq governing rules , cpu 0 1Error setting new values.
I just use the cpu_freq applet to show me that it's working. Ok Texstar. This module might not be listed in the running modules but is still available.