Home > Not Working > Car Windows And Locks Not Working

Car Windows And Locks Not Working

Contents

Didn't hear any popping noises but once I put it back together and back in...IT WORKED!!! I took off the panel, plugged it back in, and it worked fine.Now my gas guage is acting up. Good luck Was this answer helpful? Im not that familar with cars, can someone tell me what the thing looks like and how I can access it. have a peek here

The problem is that water has seeped into the switch and shorted it out. I checked all fuses, even #68 relay but still could not find problem, I drove 18 miles in 30 degree weather at nite, got home and was very confused with this When I had a similar problem with my '97, it was the driver's side switch. Dunyay wrote: My 2005 Trailblazer EXT has a couple of electrical problems that all occurred at about the same time.

Power Locks Not Working

Both were good. Festive offers that could suffer due to demonet... Within an arm's length of the bin, you toggle the power window switch with one hand while the other hand fingers a token, preparing to whip it into the basket just Polo - Derby - Lupo - Fox Golf - Jetta - Vento - Bora Golf - Jetta - Vento - Bora - Archive Topics Golf MK1 - 1974-1984 Golf MK2 -

For example, if you try to roll the passenger window up and down from the passenger door switch, will it work? I think this is in the relay box under the hood on the passenger's side.There is also a circuit breaker above the fuse box inside on the driver's side.A problem with Didn't expect it to...but it did. Power Door Lock Not Working Drivers Side After jump start no Driver window or Pwr locks..

I just literally went through all of them..... All bets are off if the door has been damaged in a crash. Send us your feedback. http://community.cartalk.com/t/power-windows-door-locks-stopped-working/78518 All goes as planned--except the window doesn't move, the token bounces back into your face, and you have to jam on the brakes, crack the door and pitch a second token

Skip navigation UploadSign inSearch Loading... Car Door Wont Lock With Remote Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Answered! BUY AUTO PARTS AT 1AAUTO.COM - Duration: 3:38. 1A Auto Parts 907,809 views 3:38 How to Remove Install Power Door Lock Relay - Duration: 7:22.

Car Door Wont Lock Manually

it might just be something with the drivers door switch - and also affecting all other doors.none of the switches work any of the windows (twice though the front pass. Try spray lubricantIf the lock is still  sticking, then get a can of multi-purpose spray lubricant and use the supplied tube to spray inside the lock mechanism. Power Locks Not Working Good luck. Power Locks Won't Work i checked everything!

For a frozen lock, you can use a hair dryer (or the flame from a match or lighter) to heat the key or the lock mechanism itself, to thaw it out. navigate here mari Melrose Park, IL #19 Mar 26, 2016 bubby wrote: I have a 06 chevy trailblazer and driver side door just stop working one day nothing on the door work not Sign in 3 Loading... Thanks Duane Jordan for the good info!! Car Door Wont Lock Or Unlock

Credentials confirmed by a Fortune 500 verification firm. Loading... My solution took about 2 days as I repeated all steps (except the driving & stopping). Check This Out Was this answer helpful?

Or just one? Power Door Lock Actuator Replacement The window lockout is also not working I've searched the fuse panel under the hood and also the fuse panel under the rear seat but I can't seem to locate the I've checked the fuses in these areas and none were blown.

Sign in 37 2 Don't like this video?

i always think i'll break it and/or it won't go back in place....anyway - the wire connection was unplugged!bing-bang-boom all systems fully functional again!i couldn't have done it without all this When the PDM receives this message, the PDM supplies voltage to the power window down circuit continuously until the power window reaches the bottom of its travel. New Toyota Fortuner 2016 Vs Ford Endeavour: Pri... Driver Side Door Controls Not Working HelloCustomer The power windos & door locks for your vehicle is operated by by the BCM(body control module) which uses several other parts for input & output.The thing I have seen

Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... But suggestion is to take a test light all fuze just to be sure. My 05 Tahoe I think has 11/12/2016 11/12/2016 KALAMYKID X Ask a Chevy Mechanic Get a Professional Answer. 100% Satisfaction Guaranteed. 31 Chevy Mechanics are Online Now Type Your Chevy Question this contact form Yes No Voted Undo Score 3 Cancel Comments: + very concise and informative.

When placed in either the lock or unlock positions, the switches provide a direct input to the DDM or PDM. Cancel earl Rep: 1 Posted: 02/25/2014 Options Permalink History same problem, took the master switch out used a transmission magnet on the 3 relays swiping the magnet back and forth. My fiances truck has the same problem...twice. Just be careful when taking it apart ) Now I don't know if it was the cleaning of the switch or the new battery ( the old one had good power

Look for damage, but also look for such things as pine sap, fossilized Froot Loops or other foreign objects that might make the window stick or bind. I did get it resolved doing the following; -make sure the battery is fully charged, no corrosion on the battery post or leads -check the fuse, replace if blown -drive the Years 1999 to 2007. - Duration: 11:04. Chevrolet Trailblazer prices reduced in India Chevrolet Beat Essentia sedan spied testing ahe...

Then window was down when about a month later they stopped working. Disconnect your battery..Just the positve cable(red) Important part.....leave it off for 15 minutes before you put cable back on everything will reboot properly Take care Bobby Was this answer helpful? Pulling the fuse or breaker cuts the power and resets the circuit. Finally I pulled the door switch and took it apart ( 4 screws ) cleaned the contacts and re assembled. ( all very easy.

>